DATaRec®4 Series- ZODIAC Data Systems GmbH (Formerly Heim Systems GmbH)

Nowadays higher and higher claims are put concerning exactness, flexibility and speed to the measuring labs. In shorter cycles prototypes or modifications have to be validated and reports must be provided. These shorter intervals and raised requirements call for better accuracy and extended channel number to be measured and processed at the same time. In addition to that systems are required to support the user during the day-to-day applications with low channel count, but should also support a substantially bigger channel count if needed. Also so-called trouble shooting applications are in many areas already part of the agenda.

These applications normally need a very low number of channels. However, in this case the user must be able to react extremely adaptably, because he should be able to measure "close" to the problem. Up to now these different applications could be only supported by a measuring lab with different hardware components at hand. These can be combined in the rarest cases with each other to build up a multi-channel system. The handling is different and identical results are not to be expected.

	modular architecture with "unlimited" channel count
	components can be used as compact solution or as a decentralized data acquisition system
	standard interfaces to analysis systems (IEEE1394b, USB 2.0, Ethernet)
	signal interface modules with integral sensor supply and signal conditioning (microphone, strain, acceleration, pressure, ICP etc.)
	signal interface modules for digital data (AES/EBU, CAN etc.)
	digital signal processing for high-qualitiy data
	A/D-converter with 24 bit resolution
	dynamic > 110 dB; phase error < 0.2°
	sampling rates upto 30 Ms/s
	galvanical isolation between modules

Signals from various signal sources are conditioned and digitized to be either directly analyzed or to be stored for later evaluation. The system supports standard computer interfaces.

Miniature system

Single module system for direct link to the PC via USB

Compact system

Centralized acquisition system with up to 192 channels

Distributed data acquisition system

Remotely located modules (up to 192 channels) with interconnecting cable lengths of up to 100 meters.

Distributed multi channel system

M3 INTEGRA

The M3 INTEGRA data acquisition and analysing system includes all functions from signal conditioning over data acquisition to data analysis. In its basic configuration it only measures 31 x 31 x  10 cm, weighs less than 10 kg and has an integrated, super-bright TFT display. Measurement data can be acquired with a maximum total sampling rate of 910 kilo samples per second with a resolution of 16 bit. All channels are acquired simultaneously without time-skew. The supply voltage can range from 10 - 32 V DC.  In case of an interruption of the board net a rechargeable power unit is integrated.

Modules

Various acquisition modules for the M3 INTEGRA system have been developed so that a whole range of different measurement categories can be acquired using only one data acquisition system. The table below helps you to find out which module you need for your measurement task:

Application Modules to be used Accelerations   - with ICP® based sensors ICP®-12/24/48 - with STG based sensors STG-08 STG-08-HS STG-08-L     Bends, strains, pressure, force, length   with resistive sensors (strain gage, potentiometric sensors,...)   - full, half and quarter bridges and shunt calibration STG-08 - full bridges only / high bandwidth STG-08-HS - full bridges only STG-08-L with inductive sensors (LVDT,...)   - full and half bridges LVDT-08 (AC-STG)     Rotations, frequencies, periods, pulse width, slip, etc. CNT-02/04/08     Analogue voltage   - high number of channels ANA-16/32/F AF-12/24 - fast / high bandwidth ANA-16/32/F AF-12/24 - with galvanic isolation ANA-ISO-08 - small signals / high precision PAM-08 AF-12/24     Acoustic noise (NVH)   - Microphones with polarisation voltage and mic supply MICP-06 - Microphones without polarisation voltage (ICP® based) ICP®-12/24/48     Data from control units   - CAN CAN - CAN, CCP, XCP, RS232, RS485, J1850, LIN, etc. DEB_II     Temperature THS-08/16/24/32

For all acquisition modules various front panels with different connectors have been designed. If these are not suitable for your application, it is also possible to develop customer specific front panels

Genesis High Speed (LDS Nicolet is now Genesis HighSpeed)

The Genesis HighSpeed family share the highest sample rates and mid to high channel counts. Based on modular platforms, all can be configured to the need of the application, be it a single channel or a thousand.

With physical signal conditioners for all common sensors or featuring isolation to acquire off-ground signals even in the MegaVolt range. Sample rates range from 100 kS/s to 100 MS/s per channel.

Systems are out-of-the-box and easy-to-use. The user interface of the shared Perception software is legendary. And, the patented StatStream review technology enables instant handling of gigabytes of measurement data.

GEN5i - Portable high speed DAQ and transient recording

GEN5i is a complete, portable test laboratory. This is the integration of all components required for complex measurement tasks and which can usually only be set up with this level of performance in the laboratory. GEN5i represents the entire measurement chain:

	From the input amplifier
	The various filters
	The selection of measurement procedure with sample rate setting and trigger events
	To post processing, evaluation and storage of the data

Measuring device:

	5 slots for input modules
	Up to 40 analog input channels
	Sampling rate 200kS/s to 100MS/s per channel, depends on input module

Input modules:

	4 channel signal conditioning
	8 channel voltage input module
	4 channel 100MS/s fast digitizer
	64 channel binary or counter input
	Up to 2GB RAM per module
	Data transmission (streaming) direct to disk without file size limitation
	Up to 56 MB/s aggregate rate, StatStream technology (patent pending) Display 100 GB data in less than 10s

Options:

	IRIG and GPS Timing interface
	SCSI interface for external hard disk or RAID removable hard disk

GEN7t/16t - High speed / high channel count DAQ and transient recording for high end requirements

Obtain a perfect overview of your system with the GEN7t/16t. With GEN7t/16t, you can configure up to 1,080 synchronized channels according to your requirements. Your system grows from the first channel onwards exactly as your project changes. Stay on top, rapidly, reliably, flexibly and always with perfect precision. Up to 8 GEN "slaves" can be connected to a GEN7t/16t master, each of these 9 devices can contain between 4 and 120 channels, and all 1,080 channels can measure in synchronization with each other. Scale your system as precisely as you require it.

	sample rate: Measurement rates from 200KS/s to 100MS/s
	Channels: 1 to 1080
	Data transmission: Gigabit Ethernet
	Storage: Internal channel RAM, SCSI RAID, external HD, server or PC via Gigabit Ethernet
	Physical input amplifier: The entire bandwidth
	Gigabytes in seconds: Precisely recorded with 100MS/s – saved in seconds
	Input amplifier for each sensor - selectable via software
	Immune against electromagnetic interferences
	Basic single ended / differential isolated 200kS/s or 1MS/s at 16Bit resolution
	Fully insulated bridge amplifiers: Full bridges, half bridges, quarter bridges DC sensor Shunt calibration 200kS/s and 1MS/s
	Universal 200KS/s or 1MS/s For ICP® piezo sensors, resistance-based current measurements or galvanically isolated measurements
	High Speed 25MS/s or 100MS/s at 14Bit resolution
	Digital input 1MS/s Event counter / external clock signal Timer

Distributed measurement intelligence means measuring spatially separate but synchronously. All channels in all connected GEN7t / GEN16t are synchronous with one another. The optical synchronization concept makes it possible to create measurement sites with several GEN7t/GEN16t over distances of several hundred meters without ground loop issues.

Typical applications:

High-precision transient recorder
Data recorder for long-term monitoring

Typical application areas:

Pyrotechnics
Energy and high-voltage technology
Destructive material testing
Aerospace
Simulation

Dimension4i - Data and transient recorder in one device

Dimension4i can be used both as a data recorder and as a transient recorder – meeting the highest of demands. Dimension4i therefore combines all essential instruments in one device.

Because Dimension4i was developed in cooperation with users as a professional tool for daily use, operation of the Dimension4i is intuitive and oriented towards the requirements of use: easy to understand, easy to operate. Routine tasks are quickly completed with Dimension4i so that you can concentrate fully on your tasks as a professional.

The graphical user interface of the 15" touchscreen leads you step by step through the logical sequence of a measurement task , from setting up the measurement scenario to recording data and data analysis. The supplied software shortens the familiarization time, because being able to start tasks efficiently and rapidly means saving time, energy and money : The requirements for fast and long-term success on the market with your products.

Gain additional functions and capacity:

Doubled recording speed per channel (200kS/s versus 100kS/s)
Nearly 40% more recording capacity (100GB versus 72GB)
Larger display (15" versus 10.4")
24Bit resolution

Typical applications:

Data recorder
Transient recorder
FFT preprocessing
Signal generator

Typical application areas:

Energy and high-voltage technology
Product development
Aerospace
Vibration technology

Measuring device:

4 slots for input modules
16 analog input channels
Sampling rate 1S/s to 200kS/s per channel
Resolution 16Bit or 24Bit
Recording modes: Continuous, transient, FFT (optional)

Input modules

Dimension4i Isolation module
Dimension4i Accelerometer module


LIBERTY - Rugged, portable, battery operated DAQ

Product tests in vehicle construction and aerospace, or the commissioning and servicing of industrial infrastructures, do not take place under air-conditioned laboratory conditions. Instead, conditions usually include vibrations and shocks, spray water, dirt and extreme external temperatures.

Typical applications:

	Test driving vehicle prototypes
	Helicopter rotor tests
	Troubleshooting in outdoor areas

All-round talent for hard applications
Optimized for use outdoors and in rough conditions, as well as in flying and moving test objects

	Automotive
	Aerospace
	Vehicle construction
	Special mechanical engineering
	Industrial infrastructure

The perfect tool for all situations

	CAN / DI
	Two CAN2.0B nodes, each with 32 channels and 64Bit resolution
	DC32 with TC Option
	32 differential channels with thermocouple connection
	Standard (General Purpose) Amplifier
	8 single ended channels or 16 differential channels
	ICP® Amplifier
	For Piezo sensors such as acceleration or pressure sensors
	Bridge
	8 channels, full bridge, half bridge, quarter bridge or differential

Basic device:

	4 or 8 slots for measurement modules
	Up to 256 input channels
	Recording modes:
	Sweep : for recurring and periodic events
	Continuous: Dual Mode: Combination of Sweep and Continuous
	10/100 Mb/s Ethernet, CAT 5e STP, wireless possible (external)
	8GB internal CompactFlash card (CF)
	IP54 Splash water resistant
	Operating temperature range -10°C to +55°C (14 to 131°F)
	Input voltage range 12 to 35 VDC, 100W max
	AC operation with optional AC/DC converter, 110/220 VAC
	Battery operation
	Impact resistance as per MIL-STD-810